# Quick Answer: What Is The Weight Of Copper Wire Per Foot?

## What is the formula of steel weight?

L = 100 m.

W = 16² x 100/162 = 158 kg.

If we put 1 meter length for each diameter of steel bar in the formula then we will get the unit weight.

If we multiply the length of bars with this unit weight we will get the total weight of steel bars..

## How do you calculate the weight of steel?

HOW TO CALCULATE STEEL WEIGHT IN KGWeight of bar in kg/meter should be calculated as (d2 ÷ 162) where’d’ is the diameter of bar in mm.’L’ for column main steel in footing should be considered as minimum 30cm/as specified.For bent up bar add 0.42d in straight length of bar where’d’ is the clear depth of beam/slab.More items…

## What is the weight of MS angle?

MS Equal Angles : 25 x 25 x 3mm to 130 x 130 x 12mmSize in mmAverage Weight100 x 100 x 812.103.70100 x 100 x 1014.904.50100 x 100 x 1217.705.40110 x 110 x 813.404.0854 more rows

## Can you melt pennies and sell the copper?

As a result, with only a few wartime exceptions, any penny from 1981 or earlier — and some made in 1982 — have a high copper content. At current copper prices, the melt value of older pennies is well over two cents. Melt values are theoretical because actually melting down pennies is illegal.

## What does 500 wire weigh per foot?

1.680LBS per footHow much does 500 mcm copper wire weigh per foot? 1.680LBS per foot …

## What is formula of weight calculation?

WEIGHT (KGS ) = WIDTH X WIDTH X 0.00000785 X LENGTH. Example : A Square of size 25mm and length 1 metre then the weight shall be. WEIGHT (KGS ) = 3.14 X 0.00000785 X ((diameter / 2)X( diameter / 2)) X LENGTH.

## Is 500 Kcmil the same as 500 MCM?

MCM is the old way of denoting the size, and kcmil is the newer way of stating the same thing. So, here is an example of how this works: Lets say you are pulling a run of 500 MCM or 500 KCMIL. That means you are pulling a conductor that has a cross section of 500,000 circular mils.

## How do I calculate wire size for a bundle?

To determine the approximate diameter of a wire bundle when the wires are all the same size, find the factor for the number of wires in the bundle and multiply the wire diameter by that factor.

## How much does wire weight per foot?

Bare Copper Wire DataAWG B&S GaugeDiameter (mils)Weight per 1000 ft. (lbs.)911439.31010231.51190.724.91280.819.816 more rows

## How much does wire cost per foot?

› Copper Building Wire › THHN/THWN-2Item (sold by the foot unless noted otherwise)O.D. (inches)Price8 AWG THHN »0.213\$0.35/ft6 AWG THHN »0.249\$0.55/ft4 AWG THHN »0.318\$0.81/ft3 AWG THHN »0.344\$1.01/ft21 more rows

## What does 250 feet of Romex weigh?

Weight: 26.75 lbs.

## Is it worth the time to strip copper wire?

If you chose to strip it, you will end up with 90 pounds of copper don’t forget 10 pounds in plastic waste and in today’s market you will get \$1.90 per pound for stripped copper wire so your 90 pounds will net you \$171.00 difference of \$21.00 between stripping it or selling the way it is, just want to mention one thing …

## How do you calculate the weight of copper wire?

The copper weight is calculated by the cross section of a cable x 9.6 and will be shown in kg / km. For example FLRY 1.50 mm² has a copper weight of 14.4 kg / km (9.6 x 1.5).

## Is copper wire worth more stripped?

Rule of Thumb for Whether a Copper Wire or Cable is Worth Stripping. If the copper recovery rate is less than the price paid for insulated copper wire divided by the price paid for bare bright copper wire, it’s not worth stripping.

## How do you calculate the length of a wire?

Multiply the current figure by the diameter of the wire; for example, if the diameter of the wire is 1.5 inches, this figure would be multiplied by 1.5. The final figure should give the length of the wire.

## What does 2 0 copper weigh per foot?

AWG Copper Wire Size and Data Table Chart @ 100 Degrees FAWGDiameterWeight(in)lb/1000 ft0000 (4/0)0.4600640.5000 (3/0)0.4096507.900 (2/0)0.3648402.841 more rows

## How do I calculate the weight of a wire?

This value is the mass per centimeter for the wire. Multiply the mass per centimeter value from Step 13 by the planned length of the wire (in centimeters). This will give you the total mass of the wire, expressed in grams. Multiply the wire’s total mass by 0.0022 to convert it to pounds.